rescan-scsi-bus.sh - script to add and remove SCSI devices without rebooting

NAME  SYNOPSIS  OPTIONS  SEE ALSO 

---

NAME

rescan-scsi-bus.sh − script to add and remove SCSI devices without rebooting

SYNOPSIS

rescan−scsi−bus.sh [−−alltargets] [−−attachpq3] [−c] [−−-channels=CLIST] [−−color] [−d] [−−flush] [−f] [−−forceremove] [−−forcerescan] [−−help] [−−hosts=HLIST] [−−ids=TLIST] [−−ignore−rev] [−−issue−lip] [−i] [−−issue−lip−wait=SECS] [−I SECS] [−l] [−L NUM] [−−largelun] [−−luns=LLIST] [−m] [−−multipath] [−−nooptscan] [−−nosync] [−−remove] [−−removelun2] [−−resize] [−−sparselun] [−−sync] [−−update] [−−version] [−−wide] [HOST1 [HOST2 ...]]

OPTIONS

Option are ordered by their long name. Those without a long name are ordered as if their single letter was a long name.
−a, −−alltargets

scan all targets, not just currently existing [default: disabled]

−−attachpq3

tell kernel to attach sg to LUN 0 that reports PQ=3

−c

enables scanning of channels 0 1 [default: 0 / all detected ones]

−−channels=CLIST

scan only channel(s) in CLIST

−−color

use coloured prefixes OLD/NEW/DEL

−d

enable debug [default: 0]

−f, −−flush

flush failed multipath devices [default: disabled]

−−forceremove

remove stale devices (DANGEROUS)

−−forcerescan

remove and readd existing devices (DANGEROUS)

−h, −−help

print usage message then exit

−−hosts=HLIST

scan only host(s) in HLIST

−−ids=TLIST

scan only target ID(s) in TLIST

−−ignore−rev

ignore (firmware) revision change. This is the third text field (4 bytes long) in a standard INQUIRY response.

−i, −−issue−lip

issue a FibreChannel LIP reset [default: disabled]

−I SECS, −−issue−lip−wait=SECS

issue a FibreChannel LIP reset and then wait SECS seconds.

	−L NUM		activates scanning for LUNs 0−−NUM [default: 0]
	−l		activates scanning for LUNs 0−−7 [default: 0]

−−largelun

tell kernel to support LUNs > 7 even on SCSI2 devs

−−luns=NLIST

scan only lun(s) in NLIST

−m, −−multipath

update multipath devices [default: disabled]

−−nooptscan

don’t stop looking for LUNs is 0 is not found

−−nosync

do not issue a sync [default: sync if remove]

−r, −−remove

enables removing of devices [default: disabled]

−−reportlun2

tell kernel to try REPORT_LUN even on SCSI2 devices

−s, −−resize

look for resized disks and reload associated multipath devices, if applicable

−−sparselun

tell kernel to support sparse LUN numbering

−−sync

issue a sync [default: sync if remove]

−u, −−update

look for existing disks that have been remapped

−V, −−version

shows version string then exits. The version string is a numeric datestamp of the form YYYYMMDD.

−w, −−wide

scan for target device IDs 0−−15 [default: 0−−7]

Host numbers may thus be specified either directly on cmd line (deprecated) or with the −−hosts=LIST parameter (recommended).

Arguments to options that end in LIST (e.g. TLIST) can have this form:
A[−B][,C[−D]]...
which is a comma separated list of single values and/or ranges (no spaces allowed).

SEE ALSO

There is a brief descripion here: https://fibrevillage.com/storage/585-rescan-scsi-bus-sh-script-for-adding-and-removing-scsi-devices-without-rebooting

sg3_utils Homepage: https://sg.danny.cz/sg

---